INDUSTRIAL SACK LINES
New
W&H Complete multiwall line: W&H In-line flexo printer Alina 1209, W&H Tuber AM 2145, W&H Bottomer AD 2378 with W&H Transystem 9350 year 1994
W&H Complete multiwall line year 1994: W&H In-line flexo printer Alina 1209, W&H Tuber AM 2145 4 plies stepped end cut, W&H Transystem 9350, W&H Bottomer AD 2378 with 1 valve unit. In good working condition. Visible in operation
Description
W&H Complete multiwall line: W&H In-line flexo printer Alina 1209, W&H Tuber AM 2145, W&H Bottomer AD 2378 with W&H Transystem 9350 year 1994
- W&H In-line flexo printer Alina 1209
- Year: 1994
- Disconnected ( the owner doesn’t use it, and currently printer is not installed in-line)
- 3 colors ( there is deck for 4th color to add)
- For paper and long print repeats printing
- Material: kraft paper 40-250 g/m2
- Max web width: 1350 mm
- Max print width: 1320 mm
- Print repeat min-max: 450-1700 mm (with repeat lengths under 600 mm, the plate cylinder hasn’t shaft)
- Gear pitch (module 3.183): 10 mm
- Mechanical speed: max. 300 m/min
- Plate cylinder bearing: with needle bearing
- Anilox roller, hard-chromed, with 80 lines/cm, diameter 178,25 mm
- Available only one size of cylinder
- Fontain roller with Elastomer coated: dia 182 mm
- Fontain roller drive gears: i = 1:3
- Power consumption: 3×380 V with neutral, 50 Hz
- Overall dimensions approx.: LxWxH 3,6m x 4,0m x 1,3 m (with 2 color decks), 2,4 m (with 4 color decks)
- Printer’s electronic distribution board is in good condition
- W&H Tuber AM 2145
- Year: 1994
- 4 plies
- Stepped end cut
- The Tuber doesn’t have the original flush cut unit, but the owner produces “flush cut” free-film sacks
- Min-max tube width (flat tubes): 260 – 600 mm
- Min-max cut-off length: 400 – 1050 mm
- Max roll width: 1230 mm
- Max roll diameter: 1300 mm
- Number of rolls: 1- 4
- Max output: 350 tubes/min. The owner makes 260 tubes/min (for cement sacks)
- Upgrades since year 2020 done by local team are as follows:
- New microperforation unit have been installed. Every station has 3 kinds of needles at the moment. 4th one can be added. Needles gets up when the machine stops, gets down when it is activated
- The current FIFE system has been completely replaced with new system
- Maintenance-free engines have been installed
- Level sensors are changed at spot pasting unit
- The puller and tow wheels were replaced with rubber wheels on cut-off unit
- W&H Print Control System (PCS) have been installed: the unit is supplied originally from W&H
- Main drive motor and packing motor have been switched from AC motor to DC motor
- The fault detection system has been integrated. Codes showing the location of each fault can be displayed from the panel
The mechanical switches on turning station (between tuber and bottomer) has been changed into magnetic switches. Codes showing the location of each faulty switches can be displayed from the panel - Weight: approx 31.000 kg
- Electrical installation: 48 kW
- Power consumption: 380V, 50Hz with MP
- Air consumption at 5 – 6 bar: 220 NL/min
- W&H Transystem 9350 year 1994
- W&H Bottomer AD 2378
- Year: 1994
- With 1 valve unit
- Min-max tube length (for smallest bottom): 510 – 930 mm
- Min-max tube length (for largest bottom): 600 – 1020 mm
- Min-max tube width: 280 – 550 mm
- Bottom center distance: 280 – 700 mm
- Min-max bottom width: 85 – 130 mm
- Min-max bottom width open: 230 – 320 mm
- Min-max sack width: 280 – 550 mm
- Min-max sack length for smallest bottom: 365 – 785 mm
- Min-max sack length for largest bottom: 410 – 830 mm
- Max output: 250 sacks/min. The owner makes 230 sacks/min (for cement sacks)
- Machine has PCS system in the patch unit
- Valve unit:
- Type of valve: standard and tube valve
- Min-max length: 80 – 220 mm
- Min-max cut-off length: 80 – 220 mm
- Min-max reel width: 100 – 280 mm
- Bottom patch:
- Min-max cut-off length: 190 – 500 mm
- Bottom patch printer 3 colors
Upgrades since year 2020 done by local team are as follows: - Main drive motor and packing motor have been switched from AC motor to DC motor
- The fault detection system has been integrated. Codes showing the location of each fault can be displayed from the panel
- Print Control System (PCS)
- Bottom closing sheets have been replaced with a system that opens and closes manually. (In original, you have to change the bottom closing sheets everytime you change the bottom dimension. But now, you just adjust the the sheet according to 9cm, 10cm 11cm 12cm… bottom)
- S-Belt
- All the aligner BST motor and system on the machine have been replaced with a new generation edge alignment system
- PLC is not present
- Arcomat and Transystem 2 are not present
- Space requirements: approx L 22-28 m, W 5 m, H 2-4 m
- Weight: approx 17.000 kg (without bottom patch unit)
- Electrical data:
- PLC model SIMATIC S5 135U
- Print control system PLC model S7 1500
- Tuber main drive PLC model ABB PM 5032-T-ETH
- Tuber turning station PLC model S7 1200
- Bottomer print control system PLC model S7 1500
- Bottomer main drive LC model ABB PM 5032-T-ETH
- Packaging station and S Drum motor + driver changed into ABB AC
- Power consumption: approx 35 kW – 40kW/380V 3-phase
- Compressed air 5 bar: 1200 NL/h
- Total power: 120 kWa
- In good working condition
- Visible in operation
- Availability: August – September 2025
About brand
German brand
2019 marks the 150th anniversary of Windmöller & Hölscher. It is one of largest supplier of printing machines extrusion lines and bag making machines and well known in the industry. For 150 years, W&H has been shaping the future. W&H ideas have shaped the flexible packaging market: From the conical bag machine in 1869 to packaging 4.0 and beyond.
Garant Maschinen, part of W&H group supplies paper bag making machines for flat satchel and block bottom bags, sack making equipment and printing and finishing machines.
W&H POLYREX SF 3708 year 1999
W&H Complete multiwall line: Tuber AM 2185, In line printer Flexa 820, Bottomer AD 2390 with Trans System 2 and W&H palletizer Arcomat 2 year 2006
How to get it?
CBS SALES SUPPORT
- Quick and honest answers
- No automated service, person to person approach
- 100% safe and secure
DISMANTLING & INSTALLATION
Grow your business with CBS Company.
CBS Company provides complete technical service. Our technical staff is complete with mechanics, electricians, and operators: we will not only install your machine but will start it up and educate your operators.
Are we available for any questions after the work is done?
The answer is YES.
We stay in touch online with our clients after the machine is installed, we are there for you 24/7.
If you wish, CBS Company helps you with the delivery of machine door to door. We can work with your shipping agent or recommend you the one if you are new to this. You are safe and satisfied if you choose to work with CBS Company on the turnkey basis projects.
We welcome you to read more about our services.
